Conel CR10 v2 Manual de usuario

CDMA router CR10 v2USER’S MANUAL LUCOM GmbH * Ansbacher Str. 2a * 90513 Z

4. CONTENTS OF PACKAGE4. Contents of packageBasic delivered set of router includes:• router,• power supply,• crossover UTP cable,• two external antenn

5. ROUTER DESIGN5. Router design5.1 Router versionsCR10 v2 router is supplied in the following versions:Box SIM1 SIM2 I/O USB PORT1 PORT2 ETHCR10 v2B

5. ROUTER DESIGN5.2 Delivery identificationTrade name Type name OtherCR10 v2B CR-10-v2 Basic versionCR10 v2B SL CR-10-v2 Basic version in the metal box

5. ROUTER DESIGN5.3 Version of firmware moduleEach operator can have another CDMA network, so it is necessary to generate a specialfirmware for each ope

5. ROUTER DESIGN5.4 Ordering codesOrder codes are given for the Polish operator Orange. Another operator can be selectedby changing two digits accordi

5. ROUTER DESIGN5.5 Basic dimensions of plastic boxFigure 10: Basic dimensions of plastic box5.6 Basic dimensions of met al boxFigure 11: Basic dimens

5. ROUTER DESIGN5.7 Mechanical dimensions and mounting recommendationsMounting recommendations:• possibility to be put on a work surface,• DIN rail wi

5. ROUTER DESIGN• For every cables we recommend to bind the bunch according to the following picture, werecommend for this use:– Length of the bunch (

5. ROUTER DESIGN5.8 Removing from the DIN railDefault position of CPD2 holder (or CKD2 holder for SL version), which is used formounting the router on

5. ROUTER DESIGN5.9 Description of the front panelOn the front panel is located:Caption Connector DescriptionPWR 2-pin Connector for the power supply

USED SYMBOLSUsed symbolsDanger – important notice, which may have an influence on the user’s safety or the functionof the device.Attention – notice on

5. ROUTER DESIGN5.9.1 Status indicationAbout router status inform eight led indicators on the front panel and on every port are twoLED indicators, whi

5. ROUTER DESIGN5.9.2 Power connector PWRPanel socket 2-pin.Pin number Signal mark Description1 VCC(+) Positive pole of DC supply voltage (+10 to +30

5. ROUTER DESIGN5.9.3 Antenna connector ANT, DIV (alternatively WIFI or WMBUS)Main and diversity antennas are connected to the router using the SMA co

5. ROUTER DESIGN5.9.4 SIM card readerThe SIM card reader for 3 V and 1,8 V SIM cards is located on the front panel of the router.To initiate the route

5. ROUTER DESIGNFigure 27: Ethernet connectorATTENTION! Port ETH is not POE (Power Over Ethernet) compatible!Ethernet cable plug into the RJ45 connect

5. ROUTER DESIGN5.9.6 PORT1The PORT1 is equipped on customer’s request with one of the offered expansion ports:• RS232• RS485/422• ETHERNET• MBUS• CNT

5. ROUTER DESIGNPORT2 cable plug into the RJ45 connector labeled as PORT1 (see figure below).Figure 31: PORT2 cable connection5.9.8 USB PortPanel socke

5. ROUTER DESIGNExample of connecting devices with serial interface to the USB:Figure 33: Connection PLC to the routerExample of connecting of USB flas

5. ROUTER DESIGNThe user interface I/O is for processing of binary input signal and to control (settings) ofbinary output signal. Binary output is not

5. ROUTER DESIGN5.9.10 ResetIt is important to distinguish between reset and reboot the router.Action Router behavior Invoking eventsReboot Turn off a

CONTENTSContents1 Safety instruction 12 Product disposal instructions 23 Router description 34 Contents of package 45 Router design 55.1 Router versio

6. FIRST USE6. First use6.1 Connecting the router before first useBefore you give up the router, it is necessary to connect all components needed for t

6. FIRST USE6.2 StartThe router is set up connecting the power supply to the router. In the default settingthe router starts to login automatically to

7. TECHNICAL PARAMETERS7. Technical parameters7.1 Technical parameters of routerCR10 v2Complies with standards EN 301 526, v1.1.1,EN 62311:2008ETSI EN

7. TECHNICAL PARAMETERS7.3 Technical parameters of processor32b ARM mikroprocesorMemory 512 Mb DDR SDRAM128 Mb FLASH1 Mb MRAMInterface Serial interfac

8. RECOMMENDED LITERATURE8. Recommended literature[1] Conel: Start guide,[2] Conel: Configuration manual,[3] Conel: User’s manual – Expansion port RS23

9. POSSIBLE PROBLEMS9. Possible problemsSome network cards are able to be set in situation, when it is not possible to connect therouter. It is possib

10. FAQ10. FAQ- I can’t get from internet on equipment, which is connected to router and I have NAT en-abled.• The device’s gateway has to be configure

10. FAQ• The operator doesn’t give out address DNS servers and without DNS server’s itis impossible to connect to server dyndns.org. In log system wil

11. CUSTOMERS SUPPORT11. Customers supportYou can find current information about this product on our website:www.conel.czUpkeep-advices:• The SIM-card

CONTENTS7.1 Technical parameters of router . . . . . . . . . . . . . . . . . . . . . . . . . . . 267.2 Technical parameters of module . . . . . . . .

LIST OF FIGURESList of Figures1 Contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Front panel CR10 v2B . . . .

LIST OF TABLESList of Tables1 Router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Delivery identification . . .

1. SAFETY INSTRUCTION1. Safety instructionPlease, observe the following instructions:• The router must be used in compliance with all applicable inter

2. PRODUCT DISPOSAL INSTRUCTIONS2. Product disposal instructionsThe WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive has beenint

3. ROUTER DESCRIPTION3. Router descriptionCDMA wireless router CR10 v2 is used to wirelessly connect various equipments and de-vices via Ethernet inte